On Sale! Anritsu MS2722C Spectrum Master Handheld Cable Antenna Analyzer – AAATesters.com
Click for Product Info and Updated Pricing
Anritsu MS2722C Spectrum Analyzers
SKU: 9S68
Anritsu MS2722C High Performance Spectrum Master
Anritsu’s high performance handheld spectrum analyzer provides the wireless professional the performance needed for the most demanding measurements in harsh RF and physical environments. Whether it is for spectrum monitoring, broadcast proofing, interference analysis, RF and microwave measurements, regulatory compliance, or Wi-Fi and wireless network measurements, the Spectrum Master is the ideal instrument for making fast and reliable measurements.
Spectrum and Interference Analyzer Highlights
- Measure: Occupied Bandwidth, Channel Power, ACPR, C/I
- Interference Analyzer: Spectrogram, Signal Strength, RSSI
- Dynamic Range: > 104 dB in 1 Hz RBW
- DANL: –160 dBm in 1 Hz RBW
- Phase Noise: –100 dBc/Hz @ 10 kHz offset at 1 GHz
- Frequency Accuracy: ±25 ppb with GPS On
- 1 Hz to 10 MHz Resolution Bandwidth (RBW)
- Traces: Normal, Max Hold, Min Hold, Average, # of Averages
- Detectors: Peak, Negative, Sample, Quasi-peak, and true RMS
- Markers: 6, each with a Delta Marker, or 1 Reference with 6 Deltas
- Limit Lines: up to 40 segments with one-button envelope creation
- Trace Save-on-Event: crossing limit line or sweep complete
Anritsu MS2722C
Capabilities and Functional Highlights
- LTE, TD-LTE
- GSM/EDGE
- W-CDMA/HSPA+
- TD-SCDMA/HSPA+
- CDMA, EV-DO
- Fixed, Mobile WiMAX
- AM/FM/SSB Demodulator
- Zero-span IF Output
- Gated Sweep
- GPS tagging of stored traces
- Internal Preamplifier standard
- High Accuracy Power Meter
- 4, 6, 8, 18, 26 GHz USB Sensors
- Channel Scanner
- 8.4 inch Display
- Burst Detect
- < 5 minute warm-up time
- 2.5 hour battery operation time
- Ethernet/USB Data Transfer
MS2722C
Specifications:
| Smart Measurements | Field Strength (uses antenna calibration tables to measure dBm/m2, dBW/m2, V/m, A/m, Watt/m2, Watt/cm2, or dBmV/m) Occupied Bandwidth (measures 99 % to 1 % power channel of a signal) Channel Power (measures the total power in a specified bandwidth) ACPR (adjacent channel power ratio) AM/FM/SSB Demodulation (wide/narrow FM, upper/lower SSB), (audio out only) C/I (carrier-to-interference ratio) Emission Mask (recall limit lines as emission mask) |
| Setup Parameters | Frequency: Center/Start/Stop, Span, Frequency Step, Signal Standard, Channel # Amplitude: Reference Level (RL), Scale, Attenuation Auto/Level, RL Offset, Pre-Amp On/Off, Detection Span: Span, Span Up/Down (1-2-5), Full Span, Zero Span, Last Span Bandwidth: RBW, Auto RBW, VBW, Auto VBW, RBW/VBW, Span/RBW File: Save, Recall, Delete, Directory Management Save/Recall: Setups, Measurements, Limit Lines, Screen Shots JPEG (save only), Save-on-Event Save-on-Event: Crossing Limit Line, Sweep Complete, Save-then-Stop, Clear All Delete: Selected File, All Measurements, All Mode Files, All Content Directory Management: Sort Method (Name/Type/Date), Ascend/Descend, Internal/USB, Copy Application Options: Impedance (50 Ω, 75 Ω, Other) |
| Sweep Functions | Sweep: Single/Continuous, Manual Trigger, Reset, Detection, Minimum Sweep Time, Trigger Type Sweep Mode: Fast, Performance, No FFT, Burst Detect Detection: Peak, RMS/Avg, Negative, Sample, Quasi-peak Triggers: Free Run, External, Video, Delay, Level, Slope, Hysteresis, Holdoff, Force Trigger Once |
| Trace Functions | Traces: Up to three Traces (A, B, C), View/Blank, Write/Hold, Trace A/B/C Operations Trace A Operations: Normal, Max Hold, Min Hold, Average, # of Averages, (always the live trace) Trace B Operations: A –> B, B <–> C, Max Hold, Min Hold Trace C Operations: A –> C, B <–> C, Max Hold, Min Hold, A – B –> C, B – A –> C, Relative Reference (dB), Scale |
| Marker Functions | Markers: Markers 1-6 each with a Delta Marker, or Marker 1 Reference with Six Delta Markers, Marker Table (On/Off/Large), All Markers Off Marker Types: Style (Fixed/Tracking), Noise Marker, Frequency Counter Marker Marker Auto-Position: Peak Search, Next Peak (Right/Left), Peak Threshold %, Set Marker to Channel, Marker Frequency to Center, Delta Marker to Span, Marker to Reference Level Marker Table: 1-6 markers frequency and amplitude, plus delta markers frequency offset and amplitude |
| Limit Line Functions | Limit Lines: Upper/Lower, On/Off, Edit, Move, Envelope, Advanced, Limit Alarm, Default Limit Limit Line Edit: Frequency, Amplitude, Add Point, Add Vertical, Delete Point, Next Point Left/Right Limit Line Move: To Current Center Frequency, By dB or Hz, To Marker 1, Offset from Marker 1 Limit Line Envelope: Create Envelope, Update Amplitude, Number of Points (41), Offset, Shape Square/Slope Limit Line Advanced: Type (Absolute/Relative), Mirror, Save/Recall |
| Frequency | Frequency Range: 9 kHz to 9 GHz (tunable to 0 Hz), Preamp 100 kHz to 9 GHz Tuning Resolution: 1 Hz Frequency Reference: Aging: ±1.0 ppm/10 years Accuracy: ±0.3 ppm (25 °C ±25 °C) + aging Auto-sensing External Frequency: Reference 1, 1.2288, 1.544, 2.048, 2.4576, 4.8, 4.9152, 5, 9.8304, 10, 13, 19.6608 MHz Frequency Span: 10 Hz to 9 GHz including zero span Sweep Time: 10 µs to 600 seconds in zero span Sweep Time Accuracy: ±2 % in zero span |
| Bandwidth (Performance Sweep Mode) | Resolution Bandwidth (RBW): 1 Hz to 10 MHz in 1–3 sequence ±10 % (–3 dB bandwidth) Video Bandwidth (VBW): 1 Hz to 10 MHz in 1–3 sequence (–3 dB bandwidth) RBW with Quasi-Peak Detection: 200 Hz, 9 kHz, 120 kHz (–6 dB bandwidth) VBW with Quasi-Peak Detection: Auto VBW is On, RBW/VBW = 1 |
| Spectral Purity | SSB Phase Noise at 1 GHz: –100 dBc/Hz @ 10 kHz offset from carrier (–104 dBc/Hz typical) –102 dBc/Hz @ 100 kHz offset from carrier (–107 dBc/Hz typical) –107 dBc/Hz @ 1 MHz offset from carrier (–114 dBc/Hz typical) –120 dBc/Hz @ 10 MHz offset from carrier (–129 dBc/Hz typical) |
| Amplitude Ranges | Dynamic Range: > 104 dB @ 2.4 GHz, 2/3 (TOI-DANL) in 1 Hz RBW Measurement Range: DANL to +30 dBm Display Range: 1 to 15 dB/div in 1 dB steps, ten divisions displayed Reference Level Range: –150 dBm to +30 dBm Attenuator Resolution: 0 to 65 dB, 5 dB steps Amplitude Units: Log Scale Modes: dBm, dBV, dBmv, dBµV Linear Scale Modes: nV, µV, mV, V, kV, nW, µW, mW, W, kW Maximum Continuous Input: +30 dBm Peak, ±50 VDC (≥ 10 dB Attn) +23 dBm Peak, ±50 VDC (< 10 dB Attn) +13 dBm Peak, ±50 VDC (Preamp On) |
| Amplitude Accuracy | 20 °C to 30 °C after 30 minute warm-up: Typical: ±0.5 dB, 100 kHz to 9 GHz Maximum: ±1.3 dB, 100 kHz to 9 GHz –10 °C to 50 °C after 60 minute warm-up: Add ±1.0 dB, 100 kHz to 9 GHz |
| Displayed Average Noise Level (DANL) | DANL in 1 Hz RBW, 0 dB attenuation: Preamp Off: Preamp On: 10 MHz to 4 GHz –141 dBm –160 dBm > 4 GHz to 9 GHz –134 dBm –156 dBm |
| Spurs | Residual Spurs: Preamp Off (RF input terminated) –90 dBm 9 kHz to 9 GHz Preamp On (RF input terminated) –100 dBm 1 MHz to 9 GHz Input-Related Spurs: (–30 dBm input, span < 1.7 GHz) –60 dBc, –70 dBc typical |
| Third-Order Intercept (TOI) | 2.4 GHz: +15 dBm 50 MHz to 9 GHz: +20 dBm typical |
| P1dB | < 4 GHz: +5 dBm typical 4 GHz to 9 GHz: +12 dBm typical |
| Second Harmonic Distortion | 50 MHz: –54 dBc < 4 GHz: –60 dBc typical > 4 GHz: –75 dBc typical |
| VSWR | (> 10 dB input attenuation) < 9 GHz 1:5:1 typical |
| General | |
| Setup Parameters | System: Status (Temperature, Battery Info, S/N, Firmware Ver, IP Address, Options Installed) Self Test, Application Self Test GPS (see Option 31) System Options: Name, Date and Time, Ethernet Configuration, Display, Volume Display (Brightness, Default Colors, Black and White, Night Vision, High Contrast) Language (English, French, German, Spanish, Chinese, Japanese, Korean, Italian, Russian, User defined) Share Center Frequency and Power Offset between Modes Reset (Factory Defaults, Master Reset, Update Firmware) File: Save, Recall, Delete, Directory Management Save/Recall: Setups, Measurements, Screen Shots JPEG (save only) Delete: Selected File, All Measurements, All Mode Files, All Content Directory Management: Sort Method (Name/Type/Date), Ascend/Descend, Internal/USB, Copy, Format USB Internal Trace/Setup Memory: > 13,000 traces External Trace/Setup Memory: Limited by size of USB Flash drive Mode Switching: Auto-Stores/Recalls most recently used Setup Parameters in the Mode |
| Connectors | RF In: Type N, male, 50 Ω, Maximum Input +30 dBm, ±50 VDC GPS: SMA Female External Power: 5.5 mm barrel connector, 12 to 15 VDC, < 5.0 Amps LAN Connection: RJ48C, 10/100 Mbps, Connect to PC or LAN for Remote Access USB Interface (2): Type A, Connect Flash Drive and Power Sensor USB Interface: 5-pin mini-B, Connect to PC for data transfer Headset Jack: 2.5 mm 3-wire headset jack External Reference In: BNC, female, 50 Ω, Maximum Input –10 dBm to +10 dBm External Reference Out: BNC, female, 50 Ω, 10 MHz External Trigger: BNC, female, 50 Ω, Maximum Input ±5 VDC IF Out: BNC, female, 50 Ω, 140 MHz |
| Display | Size: 8.4 in Resolution: 800 x 600 |
| Battery | Type: Li-Ion Battery Operation: 2.5 hours, typical |
| Electromagnetic Compatibility | European Union: CE Mark, EMC Directive 89/336/EEC, 92/31/EEC, 93/68/EEC and Low Voltage Directive 73/23/EEC, 93/68/EEC Australia and New Zealand: C-tick N274 Interference: EN 61326-1 Emissions: EN 55011 Immunity: EN 61000-4-2/-3/-4/-5/-6/-11 |
| Safety | Safety Class: EN 61010-1 Class 1 Product Safety: IEC 60950-1 when used with Company supplied Power Supply |
| Environmental | Operating Temperature: –10 °C to 55 °C Maximum Humidity: 85% Shock: MIL-PRF-28800F Class 2 Storage –51 °C to 71 °C Altitude: 4600 meters, operating and non-operating |
| Size and Weight | Size: 315 mm x 211 mm x 77 mm, (12.4 in x 8.3 in x 3.0 in) Weight: 3.5 kg, (7.8 lb) |
Buy, Sell, New, Used Anritsu MS2722C
Anritsu MS2722C Spec Sheet